tlp250 2007-10-01 1 toshiba photocoupler gaa ? as ired & photo ? ic tlp250 transistor inverter inverter for air conditioner igbt gate drive power mos fet gate drive the toshiba tlp250 consists of a gaalas light emitting diode and a integrated photodetector. this unit is 8 ? lead dip package. tlp250 is suitable for gate driving circuit of igbt or power mos fet. ? input threshold current: i f =5ma(max.) ? supply current (i cc ): 11ma(max.) ? supply voltage (v cc ): 10 ? 35v ? output current (i o ): 1.5a (max.) ? switching time (t plh /t phl ): 0.5 s(max.) ? isolation voltage: 2500v rms (min.) ? ul recognized: ul1577, file no.e67349 ? option(d4) vde approved : din en60747-5-2 maximum operating insulation voltage : 890v pk highest permissible over voltage : 4000v pk (note):when a en60747-5-2 approved type is needed, please designate ?option(d4)? truth table tr1 tr2 on on off input led off off on unit in mm toshiba 11 ? 10c4 weight: 0.54 g (typ.) pin configuration (top view) 8 7 6 5 1 : n.c. 2 : anode 3 : cathode 4 : n.c. 1 2 3 4 5 : gnd 6 : v o (output) 7 : v o 8 : v cc schmatic 2+ v f i f 3- i cc (t r 1) v o gnd (t r 2) i o v o v cc 8 7 6 5 a 0.1 f bypass capcitor must be connected between pin 8 and 5 (see note 5).
tlp250 2007-10-01 2 absolute maximum ratings (ta = 25c) characteristic symbol rating unit forward current i f 20 ma forward current derating (ta 70c) i f / ta ? 0.36 ma / c peak transient forward curent (note 1) i fpt 1 a reverse voltage v r 5 v led junction temperature tj 125 c ?h?peak output current (p w 2.5 s,f 15khz) (note 2) i oph ?1.5 a ?l?peak output current (p w 2.5 s,f 15khz) (note 2) i opl +1.5 a (ta 70c) 35 output voltage (ta = 85c) v o 24 v (ta 70c) 35 supply voltage (ta = 85c) v cc 24 v output voltage derating (ta 70c) v o / ta ? 0.73 v / c supply voltage derating (ta 70c) v cc / ta ? 0.73 v / c detector junction temperature tj 125 c operating frequency (note 3) f 25 khz operating temperature range t opr ?20~85 c storage temperature range t stg ?55~125 c lead soldering temperature (10 s) t sol 260 c isolation voltage (ac, 1 min., r.h. 60%) (note 4) bv s 2500 vrms note: using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operat ing temperature/current/voltage, etc. ) are within the absolute maximum ratings. please design the appropriate reliability upon reviewing the toshiba semiconductor reliability handbook (?handling precautions?/?derating concept and methods?) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). note 1: pulse width p w 1 s, 300pps note 2: exporenential wavefom note 3: exporenential wavefom, i oph ? 1.0a( 2.5 s), i opl +1.0a( 2.5 s) note 4: device considerd a two terminal device: pins 1, 2, 3 and 4 shorted together, and pins 5, 6, 7 and 8 shorted together. note 5: a ceramic capacitor(0.1 f) should be connected from pin 8 to pi n 5 to stabilize the operation of the high gain linear amplifier. failure to provide the bypassi ng may impair the switching proparty. the total lead length between capacitor and coupler should not exceed 1cm. recommended operating conditions characteristic symbol min typ. max unit input current, on (note6) i f(on) 7 8 10 ma input voltage, off v f(off) 0 D 0.8 v supply voltage v cc 15 D 30 20 v peak output current i oph /i opl D D 0.5 a operating temperature t opr ? 20 25 70 85 c note: recommended operating conditions are given as a design guideline to obtain expected performance of the device. additionally, each item is an independent guide line respectively. in developing designs using this product, please confirm specified characteristics shown in this document. note 6: input signal rise time(fall time)<0.5 s.
tlp250 2007-10-01 3 electrical characteristics (ta = ? 20~70c, unless otherwise specified) characteristic symbol test cir ? cuit test condition min typ.* max unit input forward voltage v f D i f = 10 ma , ta = 25c D 1.6 1.8 v temperature coefficient of forward voltage v f / ta D i f = 10 ma D ?2.0 D mv / c input reverse current i r D v r = 5v, ta = 25c D D 10 a input capacitance c t D v = 0 , f = 1mhz , ta = 25c D 45 250 pf ?h? level i oph 1 i f = 10 ma v 8? 6 = 4v ?0.5 ?1.5 D output current ?l? level i opl 2 v cc = 30v (*1) i f = 0 v 6? 5 = 2.5v 0.5 2 D a ?h? level v oh 3 v cc1 = +15v, v ee1 = ?15v r l = 200 ? , i f = 5ma 11 12.8 D output voltage ?l? level v ol 4 v cc1 = +15v, v ee1 = ?15v r l = 200 ? , v f = 0.8v D ?14.2 ?12.5 v v cc = 30v, i f = 10ma ta = 25c D 7 D ?h? level i cch D v cc = 30v, i f = 10ma D D 11 v cc = 30v, i f = 0ma ta = 25c ? 7.5 ? supply current ?l? level i ccl D v cc = 30v, i f = 0ma D D 11 ma threshold input current ?output l h? i flh D v cc1 = +15v, v ee1 = ?15v r l = 200 ? , v o > 0v D 1.2 5 ma threshold input voltage ?output h l? v fhl D v cc1 = +15v, v ee1 = ?15v r l = 200 ? , v o < 0v 0.8 D D v supply voltage v cc D 10 D 35 v capacitance (input ? output) c s D v s = 0 , f = 1mhz ta = 25 D 1.0 2.0 pf resistance(input ?output) r s D v s = 500v , ta = 25c r.h. 60% 110 12 10 14 D * all typical values are at ta = 25c (*1): duration of i o time 50 s
tlp250 2007-10-01 4 switching characteristics (ta = ? 20~70c , unless otherwise specified) characteristic symbol test cir ? cuit test condition min typ.* max unit lh t plh D 0.15 0.5 propagation delay time hl t phl D 0.15 0.5 output rise time t r D D D output fall time t f 5 i f = 8ma v cc1 = +15v, v ee1 = ?15v r l = 200 ? D D D s common mode transient immunity at high level output c mh v cm = 600v, i f = 8ma v cc = 30v, ta = 25c ?5000 D D v / s common mode transient immunity at low level output c ml 6 v cm = 600v, i f = 0ma v cc = 30v, ta = 25c 5000 D D v / s all typical values are at ta = 25c test circuit 1 : i oph test circuit 2 : i opl test circuit 3 : v oh test circuit 4 : v ol 8 1 4 v cc1 0.1 f v ol v f r l v ee1 v 8 1 4 v cc 0.1 f i opl a v 6-5 8 1 4 v cc1 0.1 f v oh v i f r l v ee1 8 1 4 v cc 0.1 f i oph v 8-6 i f a
tlp250 2007-10-01 5 test circuit 5: t plh , t phl , t r t f test circuit 6: c mh , c ml c ml (c mh ) is the maximum rate of rise (fall) of the comm on mode voltage that can be sustained with the output voltage in the low (high) state. v ee1 v cc1 v o r l 0.1 f 8 i f 100 ? v o i f v o v oh gnd v ol 80% 80% t p lh t p hl t r t f v cm 90% v o 600v c mh c hl 10% t r t f 26v 3v sw :a(i f =8ma) sw :b(i f =0) 0.1 f 8 v cc v o 1 4 v cm + - a b sw i f c ml = c mh = 480 (v) t r ( s ) t f ( s ) 480 (v)
tlp250 2007-10-01 6 i f ? v f forward voltage v f (v) forward current i f (ma) 100 1.0 50 30 10 5 3 1 0.5 0.3 0.1 0.05 0.03 0.01 1.2 1.4 1.6 1.8 2.0 ta = 25 c i f ? ta ambient temperature ta (c) allowable forward current i f (ma) 40 0 0 100 20 40 60 80 10 20 30 v cc ? ta ambient temperature ta (c) allowable supply voltage v cc (v) 40 0 0 100 20 40 60 80 10 20 30 i oph, i opl ? ta ambient temperature ta (c) allowable peak output current i oph, i opl (a) 0 0 100 20 40 60 80 1 2 pw Q 2.5 s, f Q 15 khz v f / ta ? i f forward current i f (ma) forward voltage temperature coefficient v f / ta (mv / c) -1.4 0.1 0.3 0.5 1 3 5 10 30 -1.6 -1.8 -2.0 -2.2 -2.4 -2.6
tlp250 2007-10-01 7 restrictions on product use ? toshiba corporation, and its subsidiaries and affiliates (collect ively ?toshiba?), reserve the right to make changes to the in formation in this document, and related hardware, software a nd systems (collectively ?product?) without notice. ? this document and any information herein may not be reproduc ed without prior written permission from toshiba. even with toshiba?s written permission, reproduc tion is permissible only if reproducti on is without alteration/omission. ? though toshiba works continually to improve product?s quality and reliability, product can malfunction or fail. customers are responsible for complying with safety standards and for prov iding adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a ma lfunction or failure of product could cause loss of human life, b odily injury or damage to property, including data loss or corruption. before creating and producing des igns and using, customers mus t also refer to and comply with (a) the latest versions of all re levant toshiba information, including without limitation, this d ocument, the specifications, the data sheets and applic ation notes for product and the precautions and conditions set forth in the ?tosh iba semiconductor reliability handbook? and (b) t he instructions for the application that product will be used with or for. custome rs are solely responsible for all aspects of t heir own product design or applications, incl uding but not limited to (a) determining th e appropriateness of the use of this product in such design or applications; (b) evaluating and det ermining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. toshiba assumes no liability for customers? product design or applications. ? product is intended for use in general el ectronics applications (e.g., computers, personal equipment, office equipment, measur ing equipment, industrial robots and home electroni cs appliances) or for specif ic applications as expre ssly stated in this document . product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality a nd/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or se rious public impact (?unintended use?). unintended use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic s ignaling equipment, equipment used to control combustions or explosions, safety dev ices, elevators and escalato rs, devices related to el ectric power, and equipment used in finance-related fields. do not use product for unintended use unless specifically permitted in thi s document. ? do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy product, whether in whole or in part. ? product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. ? the information contained herein is pres ented only as guidance for product use. no re sponsibility is assumed by toshiba for an y infringement of patents or any other intellectual property rights of third parties that may result from the use of product. no license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. ? a bsent a written signed agreement, except as provid ed in the relevant terms and conditions of sale for product, and to the maximum extent allowable by law, toshiba (1) assumes no liability whatsoever, including without limitation, indirect, co nsequential, special, or incidental damages or loss, including without limitation, loss of profit s, loss of opportunities, business interruption and loss of data, and (2) disclaims any and all express or implied warranties and conditions related to sale, use of product, or information, including warranties or conditions of merchantability, fitness for a particular purpose, accuracy of information, or noninfringement. ? gaas (gallium arsenide) is used in product. gaas is harmful to humans if consumed or absorbed, whether in the form of dust or vapor. handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose gaas in product. ? do not use or otherwise make available product or related so ftware or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or m anufacturing of nuclear, chemical , or biological weapons or missi le technology products (mass destruction w eapons). product and related software and technology may be controlled under the japanese foreign exchange and foreign trade law and the u.s. expor t administration regulations. ex port and re-export of product or related software or technology are strictly prohibited exc ept in compliance with all applicable export laws and regulations. ? please contact your toshiba sales representative for details as to environmental matters such as the rohs compatibility of pro duct. please use product in compliance with all applicable laws and regula tions that regulate the inclusion or use of controlled subs tances, including without limitation, the eu rohs directive. toshiba assumes no liability for damages or losses occurring as a result o f noncompliance with applicable laws and regulations.
|
